Yapbuilt FRP Primer

It is used as a conditioning and adherence enhancing primer material on surfaces where YAPBUILT© FRP FIB (fabric) and LAM (plate) are to be adhered to.

The concrete surfaces to be applied should be dry, clean and dust-free, and damaged and loose concrete parts should be removed from the surface. Surfaces should be as smooth and uniform as possible. If repairs are required on the surface, YAPBUILT® series cement-based repair mortars should be preferred, and surface defects exceeding 1 mm should be corrected with appropriate repair and leveling mortars. YAPBUILT®FRP PRIMER should not be applied until the repair mortars have completed their cure.

Mixing: YAPBUILT®FRP PRIMER is supplied in ready-to-use sets according to the mixing ratio. Before starting the mixture, it should be ensured that the material temperatures are between (+15) – (+25)°C. All of component B must be emptied into component A and it must be ensured that there is no material left in component B. The mixture should be mixed with a mixer of approximately 300 rpm and a suitable mixing tip for at least 2-3 minutes, until a homogeneous mixture is obtained, making sure that there is no unmixed material on the edges and bottom of the package.

Application The material can be easily applied with a fine brush or roller. On concrete surfaces, it should be applied by impregnating with a roller, forming a thin film layer (0.1 – 0.2 mm). The operating and reaction times of resin-based systems are affected by ambient and ground temperature and relative humidity in the air. At low temperatures, the chemical reaction slows down, which increases the life of the pan, the time it can be coated, and the operating time. At the same time, as the viscosity increases, the consumption increases. High temperatures increase the chemical reaction, and the times mentioned above are correspondingly shortened. In order for the entire material to complete its cure, the ambient and floor temperature should not fall below the minimum permissible temperature. After completion of the coating, the coating must be protected from direct water contact for at least 24 hours.

During the application, the ambient and surface temperature should not be below (+5)°C and above (+35)°C. YAPBUILT® FRP systems should be implemented by expert practitioners. The operating and reaction times of resin-based systems are affected by ambient and ground temperature and relative humidity in the air. At low temperatures, the chemical reaction slows down, which increases the life of the pan, the duration of the coatability, and the operating time. At the same time, as the viscosity increases, the consumption increases. High temperatures increase the chemical reaction, and the times mentioned above are correspondingly shortened. In order for the entire material to complete its cure, the ambient and floor temperature should not fall below the minimum permissible temperature. After completion of the coating, the coating must be protected from direct water contact for at least 24 hours. YAPBUILT® FRP PRIMER is supplied in ready-to-use sets. During the application, solvents such as solvents should not be added to the mixture. Care should be taken to prepare enough material to be used during the working period. Mixing must necessarily be carried out with the help of suitable mechanical mixers. Manual mixing should not be done. In applications to be made in special situations (different weather conditions, different application areas, etc.) that are not specified in the information sheet, consult YAPKİM YAPI KİMYA SANAYİ A.Ş. Technical Service

It is approximately 0.15 – 0.25 kg/m2.

5.00 kg set
Component A: 3.45 kg Metal Bucket
Component B: 1.55 kg Metal Bucket

ıt should be stored in its unopened original packaging, in a cool and dry environment, protected from frost. In short-term storage, a maximum of 3 pallets should be placed on top of each other and shipment should be made with a first-in, first-out system. In long-term storage, pallets should not be stacked on top of each other. Under proper storage conditions, it is 18 months from the date of manufacture. Opened packages should be stored under appropriate storage conditions and used within a week.

First of all, all necessary Occupational Health and Safety should be applied in the application areas and the operations should be carried out by people who have technical knowledge and equipment. All changes made should be in accordance with the Occupational Health and Safety instructions. It is mandatory to use all work equipment such as work clothes, protective gloves/glasses/masks specified in accordance with the Occupational Health and Safety instructions during the application. The contact of the product with the skin and eyes should be absolutely prevented, in such a case, the area where the product has come into contact should be washed immediately with plenty of water and treatment should be sought without delay. The Material Safety Data Sheet (MSDS) should be examined for more information. In addition, penal sanctions; It should be carried out by people who have sufficient technical specifications, equipment and experience. This distribution responsibility is the exclusive property of the persons.

All information provided in this information sheet is advisory only. All products should be used by people with technical knowledge and suitable equipment, considering the recommendations. YAPKİM Yapı Kimya San. A.S. cannot be held responsible for any consequences that may occur during or after usage. This document is valid until a new one is issued and invalidates the old editions. YAPKİM Yapı Kimya San. A.S. may make changes in the content of the product. It is imperative to take safety precautions during product use. These measures are not just those listed above, and it is the sole responsibility of the user to take all security measures